The Sarter Way to Characterize Component

Friendly Intuitive User Interface

The LCR-8000G Series is designed to perform precision impedance measurements over a wide frequency range of 20Hz~10MHz for LCR-8110G, 20Hz~5MHz for LCR-8105G and 20Hz~1MHz for LCR-8101G.The instrument is capable of measuring 11 different parameters with0.1% basic accuracy, which meets the precision measurement requirements of components and modules used in the RF circuits. The large LCD display with single-layer operation menu of LCR-8000GSeries providesusers with ultimate convenience to plug and play without much learning time.

Pass/Fail Function with Judgment Alarm

In the Pass/Fail test, primary parameter measurement result is compared with user-defined limits and the pass or fail result is then displayed. Three methods, including absolute limit, percentage and delta limit, are available for Hi(high) and Lo(low) limit setting based on the nominal test value. The Pass/Fail test checks whether the parameter measurement result sits within the limits, then display "PASS" for within the limits, or "LO"for lower than the low limit, or "HI" for higher than the high limit. A scale and bar for displaying measurement result is shown at the center of the screen to give a graphical identification, which greatly reduces operator's load in a long time inspection work. This scale and bar also facilitate the adjustment of the variable components. Either Pass or Fail result can be set with a buzzer alarm, which makes component or material sorting easy with sound identification.

Multi Step Mode

The Multi-Step mode is capable of running a series of measurements of a component at a number of user-defined steps in sequence automatically. Total 64 programs can be saved into the non-volatile memory, and each program contains up to 30 test steps. The parameter and Hi/Lo limits can be set respectively for each test step. After a program being properly edited, the instrument can run through all the measurement steps either at a press of the button underthe Manual Trigger selection, or automatically run the program by detecting the connection of a DUT under the Auto Trigger selection. When all the test steps are completed, the screen shows the measurement reading of the parameter being selected for each step with Pass, HI, or LO measurement result.

Graph Mode

The graph function shows the component characteristics in visual manner. Either voltage sweep or frequency sweep can be selected for horizontal scale. Just select the parameter, and set the start/stop voltage or the start/stop frequency of the sweep, LCR-8000G will run through the sequence of measurements and show the results on a graph. This graphical parameter measurement performs the characteristic verification of components and materials over the responseto the changes in AC test frequency or AC test voltage without the need of complex programming of an external controller. When the graph gets out of the vertical range, the LCR-8000G Series can automatically adjust the scale to get full test information. On the graph the marker operation is available for detailed observation.

제품 사양

LCR-8110G

LCR-8105G

LCR-8101G

테스트 주파수

20Hz~10MHz,

20Hz~5MHz,

20Hz~1MHz,

5디지트, ±0.005%

5디지트, ±0.005%

5디지트,±0.005%

출력 임피던스

100Ω

기본 정확도

±0.1% (R, Z, X, G, Y, B, L, C)

테스트 속도

AC (>2kHz)

DC

MAX : 75ms

MAX : 30ms

FAST : 150ms

FAST : 60ms

MEDIUM : 450ms

MEDIUM : 120ms

SLOW : 600ms

SLOW : 900ms

테스트 신호 레벨

≤3MHz

>3MHz

테스트 신호 레벨 :10mVrms~2Vrms 

테스트 신호 레벨 : 10mVrms~1Vrms 

스텝 : 1mV/10mV

스텝 : 1mV/10mV

정확도 : 2%±5mV

정확도 : 2%±5mV

단락 회로 전류

최대 20mA

측정 범위

R, Z, X

0.1mΩ~100MΩ

Rdc

0.1mΩ~100MΩ

G, Y, B

10nS~1000S

L

0.1nH~100kH

C

0.01pF~1F

D

0.00001~9.9999

Q

0.1~9999.9

θ

-180˚~+180˚

측정 매개 변수

임피던스(Z), 위상 각도(θ), 인덕턴스(L), 커패시턴스(C),AC 저항(Rac), 품질 계수(Q), 

손실 계수 (D), 어드미턴스(Y), 컨덕턴스(G), 리액턴스(X), 서셉턴스(B), DC 저항(Rdc)

직렬/병렬 등가 회로

C+R, C+D, C+Q, L+R, L+Q, L+D

직렬 등가 회로

X+R, X+D, X+Q

병렬 등가 회로

C+G, B+G, B+D, B+Q, B+R, L+G

극 형식

Z+θ, Y+θ

일반

평균 기능

1~256

디스플레이

320 x 240 도트 매트릭스 LCD 디스플레이

인터페이스

RS-232, GPIB

AC 입력 전원

AC 115V(+10%/-25%), AC 230V (+15%/-14%) (선택가능),50/60Hz

치수 및 무게

330(W) x 170(H) x 340(D) mm, 약 5kg

기본 액세서리

사용 설명서 x 1, 전원 코드 x 1, 테스트 리드 LCRC-12 x 1

옵션

옵션.01

DC 바이어스박스 (최대 200V, 2MHz)

GTL-234

RS-232 케이블

GTL-248

GPIB 케이블

GTL-251

GPIB-USB-HS (HighSpeed)

GRA-404

랙 어댑터패널 (19”, 4U)

주문 정보

LCR-8101G

1MHz 고정밀 LCR 미터

LCR-8105G

5MHz 고정밀 LCR 미터

LCR-8110G

10MHz 고정밀 LCR 미터

옵션

옵션.01

DC 바이어스박스 (최대 200V, 2MHz)

GTL-234

RS-232 케이블

GTL-248

GPIB 케이블

GTL-251

GPIB-USB-HS (High Speed)

GRA-404

랙 어댑터패널 (19”, 4U)